december 2015 for automobile signal line emc components act1210 [1210 inch]* (can-bus, flexray) * dimensions code jis[eia] common mode filters act1210 ty p e act series
(2/8) 20151227 / cmf_automotive_signal_act1210_en.fm emc components reminders for using these products before using these products, be sure to request the delivery specifications. safety reminders please pay sufficient attention to the warnings for safe designing when using these products. the storage period is less than 12 months. be sure to follow the storage conditions (temperature: 5 to 40c, humidity: 10 to 7 5% rh or less). if the storage period elapses, the soldering of the terminal electrodes may deteriorate. do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). before soldering, be sure to preheat components. the preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150c. soldering corrections after mounting should be within the range of the conditions determined in the specifications. if overheated, a short circuit, performance deterioration, or lifespan shortening may occur. when embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. self heating (temperature increase) occurs when the power is turned on, so the tolerance should be sufficient for the set therm al design. carefully lay out the coil for the circuit board design of the non-magnetic shield type. a malfunction may occur due to magnetic interference. use a wrist band to discharge static electricity in your body through the grounding wire. do not expose the products to magnets or magnetic fields. do not use for a purpose outside of the contents regulated in the delivery specifications. the products listed on this catalog are intended for use in general electronic equipment (av equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. the products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. if you intend to use the products in the applications listed below or if you have special requirements exceeding the range or c onditions set forth in the each catalog, please contact us. (1) aerospace/aviation equipment (2) transportation equipment (electric trains, ships, etc.) (3) medical equipment (4) power-generation control equipment (5) atomic energy-related equipment (6) seabed equipment (7) transportation control equipment (8) public information-processing equipment (9) military equipment (10) electric heating apparatus, burning equipment (11) disaster prevention/crime prevention equipment (12) safety equipment (13) other applications that are not considered general-purpose applications when designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securi ng protection circuit/device or providing backup circuits in your equipment. reminders
(3/8) 20151227 / cmf_automotive_signal_act1210_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. emc components common mode filters for automobile signal line features compact products (3225 size), whose characteristics are equivalent to that of conventional products (act45b, act45r). common mode filters for can-bus/flexray, compatible with an operating temperature range of C55 to +150c. application can-bus, flexray system. part number construction operating temperature range, package quantity, product weight overview of act1210 type act1210 - 110 - 2p - tl 00 series ? type name inductance(typ.) number of lines packaging style internal code (h) 110 11 2p 2 lines tl ?330mm reel 00 220 22 510 51 101 100 type temperature range package quantity individual weight operating temperature c (pieces/reel) g act1210 C55 to +150 6,000 0.075 product compatible with rohs directive halogen-free compatible with lead-free solders aec-q200 rohs directive compliant product: see the following for more details related to rohs directive compliant products. http://produ ct.tdk.com/en/environment/rohs/ halogen-free: indicates that cl content is less than 900ppm, br content is less than 900ppm, and that the total cl and br conte nt is less than 1500ppm.
(4/8) 20151227 / cmf_automotive_signal_act1210_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. emc components act1210 type recommended reflow profile preheating soldering peak temp. time temp. time temp. time t1 t2 t1 t3 t2 t4 t3 150c 180c 60 to 120s 230c 40s max. 245c 5s natural cooling t3 t1 preheating t2 soldering t3 t3 t4 t2 t1 t: time peak t: temperature
(5/8) 20151227 / cmf_automotive_signal_act1210_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. emc components act1210 type shape & dimensions recommended land pattern circuit diagram 2.50.2 2.5max. 3.20.2 3.9max. 0.1 cz 4x 2 1 3 4 marking dimensions in mm 4.1 2.0 0.4 1.6 dimensions in mm 1 2 4 3 ? no polarity
(6/8) 20151227 / cmf_automotive_signal_act1210_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. emc components act1210 type electrical characteristics characteristics specification table derating maximum current value for the ambient temperature (ma) measurement equipment ? equivalent measurement equipment may be used. common mode impedance [10mhz 100mv] common mode inductance [100khz 100mv] stray inductance [100khz 100mv] dc resistance rated current insulation resistance rated voltage part no. ( )min. ( )typ. (h)+50/C30% (h)typ. ( )max. (ma)max. (m )min. (v)max. 300 550 11 0.05 0.4 300 10 80 ACT1210-110-2P-TL00 500 1100 22 0.06 0.5 250 10 80 act1210-220-2p-tl00 1000 2600 51 0.09 0.7 200 10 80 act1210-510-2p-tl00 2200 5100 100 0.13 1.5 150 10 80 act1210-101-2p-tl00 0 25 50 75 100 125 150 ambient temperature ( c ) 0 0.2 0.4 0.6 0.8 1 1.2 iop/i r part no. ambient temperature 125c 140c 150c ACT1210-110-2P-TL00 300 200 100 act1210-220-2p-tl00 250 166 83 act1210-510-2p-tl00 200 133 66 act1210-101-2p-tl00 150 100 50 measurement item product no. manufacturer common mode impedance 4991a keysight technologies common mode inductance 4294a keysight technologies dc resistance 4338a keysight technologies insulation resistance 4339a keysight technologies
(7/8) 20151227 / cmf_automotive_signal_act1210_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. emc components act1210 type electrical characteristics impedance vs. frequency characteristics measurement equipment ? equivalent measurement equipment may be used. product no. manufacturer 4991a keysight technologies 1 10 100 1000 100000 10000 1000 1 10 100 frequency ( mhz ) impedance ( ) 220 common mode 510 common mode 220 differential mode 510 differential mode 110 differential mode 101 differential mode 110 common mode 101 common mode
(8/8) 20151227 / cmf_automotive_signal_act1210_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. emc components act1210 type packaging style reel dimensions tape dimensions ty p e a w1 w2 n e act1210 ?3302 13.50.5 17.51 1001 2 typ. dimensions in mm ty p e a b ?d0 e f p0 p1 p2 w k t act1210 2.850.1 4.20.1 1.5+0.1/C0 1.750.1 5.50.05 40.1 40.1 20.05 12+0.3/C0.1 2.70.1 0.350.1 ?13.0 0.2 ?21.0 0.8 n e 2.0 0.5 a dimensions in mm 1.0 w2 w1 w f e p0 p1 p2 ?d0 b a t k
|
